[wpseo_breadcrumb]

Transfer files using scp: permission denied

Solutons:


Your commands are trying to put the new Document to the root (/) of your machine. What you want to do is to transfer them to your home directory (since you have no permissions to write to /). If path to your home is something like /home/erez try the following:

scp My_file.txt user_id@server:/home/erez/

You can substitute the path to your home directory with the shortcut ~/, so the following will have the same effect:

scp My_file.txt user_id@server:~/

You can even leave out the path altogether on the remote side; this means your home directory.

scp My_file.txt user_id@server:

That is, to copy the file to your desktop you might want to transfer it to /home/erez/Desktop/:

scp My_file.txt user_id@server:/home/erez/Desktop/

or using the shortcut:

scp My_file.txt user_id@server:~/Desktop/

or using a relative path on the remote side, which is interpreted relative to your home directory:

scp My_file.txt user_id@server:Desktop/

As @ckhan already mentioned, you also have to swap the arguments, it has to be

scp FROM TO

So if you want to copy the file My_file.txt from the server user_id@server to your desktop you should try the following:

scp user_id@server:/path/to/My_file.txt ~/Desktop/

If the file My_file.txt is located in your home directory on the server you may again use the shortcut:

scp user_id@server:~/My_file.txt ~/Desktop/

What fixed the “permission denied” for me was, on the remote server, change the folder ownership to root: (This can happen when you are sending a file to a non-root user, and the directory is owned by root!)
On the remote machine (copying dest.):

sudo chown (your username) (remote folder)

Also to be sure, enable all permissions on the remote folder: (Not always necessary):

sudo chmod 777 (remote folder)

I came here for “Transfer files using scp: permission denied” because I had the same error.

In my case, the file downloaded with scp would have overwritten a file owned by root, and I wasn’t root. In short, check the ownership of the file being overwritten.

Related Solutions

What is D-Bus practically useful for?

dbus does exactly what you said: it allows two-way communication between applications. For your specific example you mentioned terminator. From terminator's man page, we see: --new-tab If this is specified and Terminator is already running, DBus will be used to...

How to check ‘mdadm’ RAIDs while running?

The point of RAID with redundancy is that it will keep going as long as it can, but obviously it will detect errors that put it into a degraded mode, such as a failing disk. You can show the current status of an array with mdadm --detail (abbreviated as mdadm...

What is a “toast notification”?

A Toast is a non modal, unobtrusive window element used to display brief, auto-expiring windows of information to a user. Android OS makes relatively heavy use of them. Here's an example of a Google Chrome toast notification on Mac OS X: A list of descriptions...

Which elliptic curve should I use?

You are misreading Bernstein and Lange's advice (admittedly, their presentation is a bit misleading, with the scary red "False" tags). What they mean is not that some curves are inherently unsafe, but that safe implementation of some curves is easier than for...

How can I find files that are bigger/smaller than x bytes?

Use: find . -type f -size +4096c to find files bigger than 4096 bytes. And : find . -type f -size -4096c to find files smaller than 4096 bytes. Notice the + and - difference after the size switch. The -size switch explained: -size n[cwbkMG] File uses n units of...

Relative imports in Python 3

Explanation From PEP 328 Relative imports use a module's __name__ attribute to determine that module's position in the package hierarchy. If the module's name does not contain any package information (e.g. it is set to '__main__') then relative imports are...

How to add a class to a given element?

If you're only targeting modern browsers: Use element.classList.add to add a class: element.classList.add("my-class"); And element.classList.remove to remove a class: element.classList.remove("my-class"); If you need to support Internet Explorer 9 or lower: Add...

less searches are always case-insensitive

I'm not sure how to enable this from the command line but when you're inside of less you can toggle the behavior you want by giving the -i command to less. toggling -i                searching for /blah and /BLAH               searching for /Blah       ...

Is using nested try-catch blocks an anti-pattern?

This is sometimes unavoidable, especially if your recovery code might throw an exception. Not pretty, but sometimes there are no alternatives. I don't think its an antipattern, just widely misused. Most nested try catch's are indeed avoidable and ugly as hell,...

Create a branch in Git from another branch

If you like the method in the link you've posted, have a look at Git Flow. It's a set of scripts he created for that workflow. But to answer your question: git checkout -b myFeature dev Creates the MyFeature branch off dev. Do your work and then git commit -am...

How can I set customise settings for htop?

htop has a setup screen, accessed via F2, that allows you to customize the top part of the display, including adding or removing a "Load average" field and setting it's style (text, bar, etc.). These seem to be auto saved in $HOME/.config/htop/htoprc, which...

Is there any way to manually bring up the keyboard?

As I see an alternative keyboard may solve your issue, and this seems to be an acceptable solution, and you even mention something you cannot find -- hereby I proudly present: Hacker's Keyboard Checking its Guide, there's in fact a section suggesting such a...

How to get rid of “No match found” when running “rm *”

This behaviour is controlled by several of Zsh's globbing options. By default, if a command line contains a globbing expression which doesn't match anything, Zsh will print the error message you're seeing, and not run the command at all. You can disable this in...

How to append date to backup filename

This isn't working because the command date returns a string with spaces in it. $ date Wed Oct 16 19:20:51 EDT 2013 If you truly want filenames like that you'll need to wrap that string in quotes. $ touch "foo.backup.$(date)" $ ll foo* -rw-rw-r-- 1 saml saml 0...

What does __all__ mean in Python?

Linked to, but not explicitly mentioned here, is exactly when __all__ is used. It is a list of strings defining what symbols in a module will be exported when from <module> import * is used on the module. For example, the following code in a foo.py...